Buscar recursos académicos

Abstract Non-penetration laser welding of lap joints in austenitic stainless steel sheets is commonly preferred in fields where the surface quality is of utmost importance. However, the application of non-penetration wel...

The corrosion behavior of two wrought super duplex stainless steels (SDSS), UNS S32750 and UNS S32760, and a cast duplex stainless steel (DSS), DIN/EN 1.4517, was evaluated in 3.5 wt% NaCl and ASTM D1141 synthetic seaw...

Lean duplex stainless steels (LDSS) emerged as a competitive duplex stainless steels (DSS) where Ni is partially replaced by lower cost alloying elements such as Mn and N. However, to date there has been little to no inf...

Deformasi slot braket Stainless Steel akan mempengaruhi gaya yang diaplikasikan kepada gigi.Tujuan penelitian adalah untuk mengetahui deformasi slot braket dari lima merek braket yaitu 3M, Biom, Versadent, Ormco dan Shin...

Deformasi slot braket dapat mengurangi besar gaya torque  yang akan dihantarkan ke gigi dan jaringan pendukungnya. Beberapa braket stainless steel yang beredar dipasaran belum pernah diteliti kualitasnya dalam perawatan...

The excellent mechanical properties, high thermal conductivity and corrosion resistance combined with moderate cost make superferritic stainless steels (SFSS) commercially attractive. Though these steels are finding incr...

In our study, annealing was done to AISI 310S stainless steel at 800 °C. The effects of these annealing on structural, morphological, mechanical and electrical conductivities were investigated. From XRD results, it has ...

Abstract With the growing interest in utilizing Mg and austenitic stainless steel (ASS) in the automotive sector, joining them together in three-sheet configuration is inevitable. However, achieving this task presents co...

Duplex stainless steels fabricated by Laser Bed Powder Fusion (LPBF) exhibit refined and metastable microstructures that can be particularly sensitive to intermediate-temperature exposure. In this study, the effect of 47...

Concentration determination of stainless steel 316L and cobalt chromium remanium GM - 800 on GPMT test. Dentistry had used metals such as cobalt chromium and stainless steel in maxillofacial surgery, cardiovascular, and ...

Abstract The forming quality of metal bipolar plate (BPP) flow channels in proton exchange membrane fuel cells (PEMFCs) is a key factor affecting battery performance. A flow channel with straight sidewalls and a low thin...

Bacillus cereus adherence to stainless steel used to milk contact surfaces was observed, depending on the cleaning and sanitizing procedures applied and the physicochemical properties of the surfaces. Numbers of survivin...

Electrochemical cutting with internal electrolyte jetting is a high-efficiency and high-precision machining technology suitable for cutting workpieces with a thickness exceeding 1 mm. In this process, a metal tube with...

Closed coil spring is an additional tool in a fixed-orthodontic treatment. NiTi is an orthodontic alloy that has shape memory and elasticity features, while stainless steel has properties of malleability, low friction be...

Abstract Biofilm formation of Geobacillus thermodenitrificans, Geobacillus thermoglucosidans and Anoxybacillus flavithermus in milk on stainless steel were monitored at 55°C, 60°C, and 65°C for various incubation time...

Abstract Lithium bis(fluorosulfonyl)imide has emerged as a promising alternative to lithium hexafluorophosphate as conducting salt in battery electrolytes due to its favorable physicochemical properties. However, its ten...

ABSTRACT Tetracycline (TC) is a commonly prescribed broad‐spectrum antibiotic, and its widespread use together with its persistence in biological matrices, particularly urine, has raised serious concerns related to cli...

Laser powder bed fusion (L-PBF) technology has undergone rapid development in recent years. Owing to its advantages of high speed, efficiency, intelligence, and full flexibility, it exhibits significant potential for rea...

In this study, TiO2 nanotubes decorated with In2S3 films were fabricated by anodic oxidation followed by hydrothermal deposition. Under optimized conditions (2 mmol precursor, 12 h), the TiO2/In2S3 photoanode deliver...

Tesis Energía y Ambiente (maestría) - Instituto Tecnológico de Buenos Aires, Buenos Aires - Karlsruher Institut für Technologie, Karlsruhe, 2024 "In the global effort to reduce greenhouse gas emissions and enhance en...

We demonstrate how controlling the heat affected zone during laser powder bed fusion may be used to optimise the phase composition of additively manufactured (AM) components in-situ to reduce post-processing heat treatme...

Reinforced concrete (RC) piers have been widely studied and applied in bridge construction practice. To ensure the normal operation of RC piers under corrosive environments and seismic effects, new corrosion-resistant ma...

Abstract Increasing demands for sustainable manufacturing are accelerating the need for efficient scrap reutilization routes that extend beyond conventional remelting practices. In this context, solid-state reuse of mach...

IntroductionDental caries is a prevalent childhood condition with significant health and economic consequences. Disease management techniques, such as silver diamine fluoride (SDF) and sealants, have emerged as alternati...