Buscar recursos académicos

Aluminum (Al), a commonly used reactive metals, is widely applied in reactive material systems. However, its relatively low reactivity restricts the energy release of systems. To improve the reactivity of aluminum, we in...

Abstract: The work focuses on the preparation of polymer matrix composite materials by hand lay up the composite materials were prepared from the unsaturated polyester resin as matrix reinforced by intensification materi...

The evaporative cooling system has better advantages than conventional systems in terms of the economic costs, methods of operation, energy consumption, and no pollution, as caused by the fluorocarbon gases and their rol...

Powder compaction is the most widely used technology to fabricate polymer bonded explosives (PBX), and its parameters significantly influence the structures and mechanical properties of the final products. By conducting ...

Geothermal solid waste is one of the byproduct materials from the geothermal energy process. The silica extracted from this solid waste can be utilized as a raw material for waterproof coatings. The waterproof or hydroph...

Thanks to the ultrahigh flexibility of 2D materials and to their extreme sensitivity to applied strain, there is currently a strong interest in studying and understanding how their electronic properties can be modulated ...

Different basic materials, such as K-L zeolite, K-Al2O3, K-Mg/Al mixed oxide and MgO, were used as supports of Pt-catalysts for the dry reforming of methane (DR) reaction. The effects of the distribution of basic strengt...

With the increasing demand for enhanced mechanical properties and energy release capabilities in energetic structural materials, traditional materials struggle to concurrently achieve both high mechanical properties and ...

Refractories are defined as "non-metallic materials having those chemical and physical properties that make them applicable: for structures, or as components of systems, that are exposed to environments above 1,000 °F (...

Abstract Multi-component nanofluids have attracted increasing attention for advanced heat transfer and energy systems; however, experimental data on oxide-based quadri-hybrid nanofluids, particularly regarding their coup...

This study investigated the potential of polyvinylpyrrolidone-grafted graphene (PGR) for secondary reinforcement of SBS and microwave-activated crumb rubber (ACR) modified asphalt, aiming to clarify the underlying mechan...

Hydrogen is widely recognized as a clean and sustainable energy carrier, driving the urgent need for safe and efficient solid-state storage materials. In this study, the structural, thermodynamic, electronic, optical, an...

To enhance the total output energy and power of energetic materials, plasma that generated by electrically exploded metal wires was employed to initiate the detonation of energetic materials, thereby achieving the couple...

The objective of this study was to evaluate the effect of packaging permeability (water and oxygen) on the sensory and physical properties of white sliced bread during storage at ambient and accelerated conditions. White...

Ultrafine pure and Mn-doped SnO2 nanoparticles (NPs) were synthesized via the microwave technique. They were produced using tin chloride and hexamethylenetetramine at the molar ratio of 1:20. The concentrations of Mn in ...

We have studied the effect of the pelletization pressure on microstructural and electrical transport properties of superconducting ceramics with starting composition given by the formula Bi 1.65Pb 0.35Sr 2Ca 2.5Cu 3.5O 1...

There is a growing need for the production of certain types of asphaltic materials having good rheological properties compared with the unmodified asphaltic materials, thus many experiments were performed to prepare a mo...

The burgeoning research into two-dimensional (2D) materials opens a door to novel photonic and optoelectronic devices utilizing their fascinating electronic and photonic properties in thin-layered architectures. The hybr...

Several forms of niobium oxide were prepared, including nanostructured mesoporous materials, and their acidity properties were comprehensively investigated and compared with commercially available materials. The composit...

High-consistency silicone rubbers can be foamed with various chemical and physical blowing agents. However, due to the toxic and, therewith, harmful effects of chemical blowing agents, physical blowing agents are becomin...

This study presents a novel, modular 3D printing system for the scalable production of microbially induced calcium carbonate (CaCO3) precipitation (MICP) produced bio-materials. Through modular design principles and oper...

Abstract A novel biphasic Dy2Hf2O7-HfO2 composite was synthesized via a solid-state reaction route for potential thermal barrier coating (TBC) applications. X-ray diffraction confirmed that the reaction between Dy2O3 and...

In this study, ordered mesoporous carbons CMK-3 were prepared by a nanocasting method using SBA-15 silica as template and sucrose as carbon source. The pure CMK-3 was modified with nickel by wet impregnation method and t...

To investigate the dynamic mechanical behavior and fragmentation characteristics of layered rock under the combined effects of chemical corrosion and impact loading, split Hopkinson pressure bar (SHPB) tests were perform...