Buscar recursos académicos

Natural hydrogels are widely used for 3D-bioprinting because of their qualities fortissue engineering. Recently, hydrogels have been combined with bioactive glasses,due to their angiogenic properties that aid tissue rege...

The global shift towards sustainability has driven significant advancements in construction methodologies. Among these innovations, 3D Concrete Printing (3DCP) stands out as a transformative technology that employs gantr...

Limosilactobacillus fermentum Lf2 (Lf2) and Bifidobacterium animalis INL1 (INL1) are two autochthonous probiotic strains that produce exopolysaccharides (EPS), and some of these molecules were associated with health-prom...

Predictive modeling of natural sediment-laden flows requires rheometric protocols that are both reproducible and time-aware of sediment dynamics. This study establishes a standard measurement protocol for homogeneous sed...

Background and aim Membranes for guided bone regeneration should have a mechanical structure and a chemical composition suitable for mimicking biological structures. In this work, we pursue the development of periosteum-...

Abstract 3D printing technology enables the production of creative and personalized food products that meet consumer needs, such as an attractive visual appearance, fortification of specific nutrients, and modified textu...

The need to know the dose of X-rays to be applied to patients suffering diseases such as cancerrequires accurate and stable dosimetric devices. Currently, the use of gelatin-based dosimetershas yielded excellent results ...

Abstract Colostrum is the first mammary secretion produced after parturition and represents a biologically active fluid essential for neonatal survival, immune maturation, and early growth. Despite its importance, breed-...

Thermoplastic polymers have emerged as compelling alternatives to conventional thermosets in response to increasing environmental concerns, primarily due to their superior recyclability and enhanced sustainability charac...

Abstract Cheese emulsion is an intermediate product for the production of cheese powder and needs to be stable, homogeneous and pumpable characteristics to convey to the spray drier. This study was conducted to evaluate ...

Blends and composites were obtained by mixing commercial metallocenic linear low density polyethylene (LLDPE) and isotactic polypropylene, with different molecular weight polydimethylsiloxanes (PDMS), including a vinyl e...

Abstract Abstract Fat reduction in the formulation of cheese emulsion causes problems in its flowability and functional characteristics during spray-dried cheese powder production. In order to eliminate these problems, t...

Alginate production is estimated to be around 30,000 tonnes per year, coming from a limited number of macroalgae species. Therefore, to diversify the market and make it sustainable over time, it is important to find new ...

Septoria leaf blotch (SLB), caused by Mycosphaerella graminicola, reduces yield and grain quality of wheat (Triticum aestivum L.) by affecting the photosynthetically active area of the crop. This might influence grain pr...

Microbially-colonized sediments tend to be more resistant to erosional events than mostly abiotic sediments. However, the effect of complex microbial associations, such as microbial mats over sediments and the protection...

Abstract The earthquake Magnitude‐Frequency‐Distribution is usually modeled with the Gutenberg‐Richter law, where the b‐value controls the relative rate of small and large earthquakes. b‐value shows an inverse ...

Rock avalanches move large volumes of material causing a highly destructive power over large areas. In these events, it is possible to monitor the evolution of slopes but failure cannot be always prevented. For this reas...

The stress-strain of samples deformed until failure and the relaxation response after 50% deformation of the initial height under constant stress were obtained. Uniaxial compression and stressrelaxation tests enabled s...

Abstract Fatty acid ethanolamides (FAEs) are bioactive lipids with amphiphilic properties and potential as prodrugs. In this study, a homologous series of FAEs (C8:0–C18:0) was evaluated for solubility, hydrophobicity,...

Las conclusiones sobre los deslizamientos individualizados en la cordillera neuquina (36°-38°S), (su inducción sísmica; rechazo de la consideración de sus depósitos como till),indujo a proyectar su estudio al sur d...

Abstract The multicomponent thermal fluid (MTF) process is a pivotal technology for enhancing heavy oil recovery. However, its injection often triggers particle migration and deposition within reservoirs, leading to perm...

Objective: To investigate the use of perillaldehyde (PAE) for treating plateau insomnia and to develop a stable intranasal PAE nanomicelles in situ gel (PAE/NMs-INSG). Methods: A mouse model of plateau insomnia was estab...

Abstract The use of skim milk is a strategy to increase goat milk yogurt acceptability. However, it can negatively affect yogurt rheology because fat plays a vital role in dairy structural integrity. Thus, this study aim...

We describe polymer diffusion and its temperature dependence in poly(vinyl acetate-co-dibutyl maleate) [P(VAc-DBM)] latex films prepared from 4:1 w/w ratio of VAc:DBM. Two sets of polymers were investigated: one set cont...