Cerca risorse accademiche

Abstract Out-of-plane mechanical properties of the riveted joints restrict the performance of the wing box assembly of airplane. It is necessary to investigate the pull-through performance of the composite/metal riveted ...

According to the results of complex electrochemical, corrosion-mechanical and fractographic studies, the existence of three potential regions, in which the stress-corrosion cracking (SCC) of 17G1S (17G1S-U) steel in the ...

The necessity to reduce the weight of transport structures, such as cars and airplanes, has become more important due to gas emission regulations. In this regard, the use of hybrid structures made of steel and aluminum i...

Abstract Hydraulic actuated quadruped robots have bright application prospects and significant research values in unmanned area investigation, disaster rescue and other scenarios, due to the advantages of high payload an...

ABSTRACT This study aimed to characterize the clinical and arthroscopic presentations of horses with osteochondral fragmentation at the metacarpophalangeal and metatarsophalangeal joints at the Veterinary Hospital of the...

ABSTRACT Osteoarthritis and osteochondrosis are highly correlated to reproductive failure in bulls. This study aimed to evaluate the carpal, tarsal and interphalangeal lesions in beef zebu bulls on semen collection regim...

Abstract The current research of reconfigurable parallel mechanism mainly focuses on the construction of reconfigurable joints. Compared with the method of changing the mobility by physical locking joints, the geometric ...

Abstract Currently, conventional single-sided friction stir welding is primarily suitable for joining thin plate aluminum alloys, and its application to thick plates is still challenging in terms of welding efficiency an...

Abstract Joining metal to plastic can lighten weight of products to reduce energy consumption. However, it is difficult to achieve high-strength welding between metal and plastic. To address this problem, the methods of ...

With the continuous improvement of lightweight requirements for equipment, Mg alloys are increasingly widely used, and their joining with traditional steel materials is essential. However, Mg and Fe have almost no solid ...

Abstract The resistance spot weldability of galvanized ultra-high-strength steels is not satisfied, the joints are prone to interfacial fracture and the weldable current range is narrow. To solve the problems, a novel me...

As the water pressure of shield tunnel increases, the key to tunnel construction is to strengthen the water resistance of joints. By analyzing the characteristics of stress and deformation of the gaskets in the joints of...

Abstract Penetration and non-penetration lap laser welding is the joining method for assembling side facade panels of railway passenger cars, while their fatigue performances and the difference between them are not compl...

Concrete-filled steel tubular (CFST) truss arch bridges are widely used in long-span bridge construction due to their high strength, good stiffness, and excellent durability. However, arch rib joints, as critical load-be...

Abstract The QP980-DP980 dissimilar steel joints were fabricated by fiber laser welding. The weld zone (WZ) was fully martensitic structure, and heat-affected zone (HAZ) contained newly-formed martensite and partially te...

Abstract A novel double side friction stir Z shape lap-butt welding (DS-FSZW) process was proposed to achieve excellent mechanical properties of Al/Cu medium-thick dissimilar joints. The influence of welding parameters o...

The present study focused on the evaluation of critical influencing parameters of the FSW of AA6061-T6 and AA2024-T351 alloys. The materials properties of AA6061-T6 are heat-treatable alloys possessing properties of good...

Abstract Fracture toughness property is of significant importance when evaluating structural safety. The current research of fracture toughness mainly focused on crack in homogeneous material and experimental results. Wh...

Abstract Self-piercing riveting (SPR) has been widely used in automobile industry, and the strength prediction of SPR joints always attracts the attention of researchers. In this work, a prediction method of the cross-te...

Abstract 6082-T6 aluminum alloy is a commonly used aluminum alloy material in the field of rail transit because of its good molding properties, high mechanical properties, excellent corrosion resistance and weldability. ...

Butt welding between SLM-formed AlSi10Mg and rolled 6061 alloy (T6 state) was conducted by the tungsten inert-gas arc welding(TIG) method. The microstructure and mechanical properties of TIG welded joints under different...

A study on the microstructure, mechanical properties, and heat treatment process of pure tantalum TIG joints was conducted. Industrial computed tomography (CT), OM, and SEM were used to characterize the microstructure of...

ABSTRACT The aim of this study was to report the first case of surgical talocalcaneal arthrodesis combined with surgical drilling of the distal intertarsal and tarsometatarsal joints in a Mangalarga Marchador horse. The ...